مقطورة نصف منخفضة

FAYMONVILLE Megamax Tiefbett 2x10 t, Bolzen-Laschen-Kupplung

You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website.

Bdjdpfxsv Sw E Aj Ahwsi
Excerpt from the equipment details. Full specifications available upon request.

Neck (Gooseneck)
* Gooseneck in SNT design to optimize loading platform length
* Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable
* Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2

Kessel Bridge (Tiefbett section)
* Low bed designed as extendable Kessel bridge in SUPER LOW design
* Approx. 6,850 mm length
* With mechanical locking
* Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length

Rear Chassis
* Short version with closed outer frame and checker plate cover
* Chassis with excavator trough, closed at the rear half to accommodate air tanks

Axles
* BPW axles and suspension, all axles hydro-mechanically forced steered
* Technical axle load: 12,000 kg per axle
* Air suspension with lifting and lowering valve

Tires
* GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F)

Brake system
* Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit

Paintwork
* 6-Coat final treatment
* All-steel construction shot-blasted after welding
* 1 layer of zinc-based primer
* 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax

Trailer color
* RAL 3002 Carmine Red
* Rim color: Silver grey
* Drop side color: Natural aluminum

Accessories included
* Removable steel front wall, approx. 400 mm high
* 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit
* Spare wheel carrier in front of the gooseneck front wall
* Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm
* 2 pairs of screw-in lashing rings included (LC 5,000 daN)
* 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN)
* 2" king pin
* Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly
* Air connection with air gun at the gooseneck
* 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed
* 1 lashing ring each left and right on the front cross member (LC 10,000 daN)
* Outer side beams of the loading area prepared for removable loading floor
* Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area
* Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN)
* Cut-outs above the lashing rings in the outer carrier’s upper flange
* Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings
* The outer carriers of the low bed coated with anti-slip sand finish for slip resistance
* 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit
* 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN)
* Front and rear tapers

تمت ترجمة الإعلان تلقائياً، وقد تكون هنالك بعض الأخطاء في الترجمة.